Standard Applications

TRIPPER
You start the pump, but often forget to switch it off, resulting in OVERFLOW - wastage of both electricity and water, in addition to messing up of surroundings, and damaging walls and roof. TRIPPER switches off the pump automatically, when the tank is full.

WATER MANAGER FLIC V-1
To provide automatic control to water pump. Starts the pump when level in the overhead (destination) tank is LOW and switches it off when the tank is FULL. This is suitable where the source of water is unlimited (like groundwater or in case of a tube-well). Models to operate single-phase pumps directly or 3-phase pump through its starter coil.

WATER MANAGER FLIC V-2
As V-1 above, but also monitors level in the supplying tank, when water is being drawn from there. It stops the pump, in case water in the source tank depletes, and prevents dry running damage.

WATER MANAGER FLIC V-S (For Basement Toilets)
For sump pump automation: Starts the pump, when level in sump rises, and switches off on emptying the tank. In case level goes to a high critical point, an audio alarm is sounded, which can help warn to check the problem (optional).

WATER MANAGER FLIC V-1 D & FLIC V-2 D
When the system supplies to TWO tanks from ONE pump

WATER MANAGER FLIC-500 (Industrial Applications)
Gives Level Indication (5 stages of 20% each), Automatic Control of Pump, and Warning Alarms if level goes OUTSIDE the automation range. (Price on request, after studying requirement)

Actuating floats for Ser. 1 to 3 and Ser. No 5 are made from polypropylene, whereas for Ser. 4 and 6 these are made from Stainless steel. Each probe unit uses only ONE float.

All systems are stand-alone, fully functional, suitable for direct application. Input voltage 220 V AC. We offer control systems for most liquids. Wetted parts SS 304/316. To get your quotation, please send in detailed requirement.

Large Application

Most large buildings and Housing complexes have a requirement for storage and handling of water. Where raw water is drawn from ground, there is a further requirement of purification of water before supply. Further there is a requirement of treatment of wastewater and it's handling and disposal. It implies managing wastewater pumps through automation. Hotels, Restaurants, Dairies, Municipal corporations and Industrial users It is important for consultants and architects to design water supply and disposal in such a way as to ensure that the users never have to worry about handling pumps and checking levels as a routine. ACTIVE CONTROLS provide complete automation from Start to End in the Water Supply Scheme. Since water invariably corrodes most equipment, Active Controls' emphasis has been to supply equipment that is NOT AFFECTED by water corrosion; meaning NO MAINTENANCE. Below are some of the areas where our systems are being regularly used. This however is only a guideline and there no limit to how innovatively you like to design your process.

Localized Water Treatment Plant

Typical Water Supply Systems
This is a standard arrangement where water is drawn from a tube well (submersible pump) and pumped directly to the overhead tank. A variation to this is a sump tank where water is received from a tube well or municipal water supply and then pumped to the overhead tank. Automation system provides

• Level indication in 5 OR 10 stages depending on depth of tank
• Automatic Control of water pump. In case there are two pumps, then the control system is configured to operate i) In automatic alternate duty change at every operation. OR ii) Manual pump selector for deciding the duty and standby pump.
• Level warning alarm in case pump fails to operate.
• Other options like Control of pumps based on TIME, control of dozing pump,

When Using One Sump To Fill Two Or More Tanks
The system uses electrically operated valves to control flow in to tanks

Sump Pumps
In case of Sewage disposal systems, treatment plants , basement sumps where waste water level needs to be monitored and pumps or valves controlled, ACTIVE CONTROL systems are very reliable. These are designed to operate one or more pumps depending on inflow and discharge, and the level in sump tanks. Very effectively used in complete STP operation.

• Pump 1 switches ON at level L1 and
• Switches off at level L0
• On next operation Pump 2 switches ON at Level L1 and switches off at Level L0
• If during the operation of P1 OR P2 level rises higher to L2, the pump not operating also switches ON. At this point both pumps operate to pump out the water
• If level further rises to L3 despite both pumps operating, an audio alarm is sounded to warn the attendant of the situation.

This is a typical application. We can provide any type of controls to suit the user plan, design or requirement

Automation Of Water Supply System
Where a number of buildings are supplied water from one set of pumps, a very effective plan is through a ring-main, which supplies water to all the feeders. This type of systems is operated based on levels.

• The system is configured to operate in such a way that the pump will be switched ON when level in any ONE tank drops, but will be switched OFF, when all the tanks are full.
• All tanks are provided with normally open solenoid valves. These are independent of the water level controller and operate as Float type (Ball cock) valves. Each valve has one level controller to prevent overflow.

As each tank gets filled up, it gives the signal to the pump to switch off. Just above this level the inlet solenoid valve of this tank closes, thereby preventing overflow. When the last tank fills up, the pump switches off.

The unit may also have a level indicator to give the availability in each tank. The level indicator can be placed at any suitable location near the pump room.

Remote Monitoring & Control through GSM/GPRS Mini SCADA

Download PDF

Municipal, Rural Water Supply and Public Health Engineering.

Our Level Monitoring and Control Systems are effectively used in automation and control of Pumps, including Supervisory Control (SCADA). The pumps can be operated based on real time clock as well as Levels, with information on water availability and Pump Health. These combined with Level indication and Alarm provide comprehensive control and protection in water supply and all it's applications. Similarly these are effective in ETPs and Sewage Treatment plants to operate the complete scheme based on levels and other inputs from different sensors and monitors. Please contact us with your requirements in detail